Product ID:ENAMEL SEMI GLOSS RUST INHIBITING OD
MSDS Date:12/18/1989
FSC:8010
NIIN:00-297-2124
MSDS Number: BMSMD

CON-LUX COATINGS, INC.

226 TALMADGE ROAD
EDISON, NJ 08818-0847
US

Emergency Phone: 201-287-4000

Info Phone: 201-287-4000

Cage: 60189

CON-LUX COATINGS INC

847 EDISON, NJ 08818-0847 US

Telephone: 732-287-4000

Cage: 60189

MINERAL SPIRITS (VAPOR PRESSURE 2.00 MM HG @ 20C) (LEL

CAS: 8052-41-3

RTECS: WJ8925000

Fraction By Weight: > 1%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM; 9293

CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

Fraction By Weight: > 1%

ACGIH TLV: 3.5 MG/M3

ZINC OXIDE (AS NUISANCE DUST)

CAS: 1314-13-2

RTECS: ZH4810000

Fraction By Weight: 4%

OSHA PEL 15MG/M3 TDUST/5 FUME

ACGIH TLV: 10MG/M3 TDUST; 9293

LEAD ORTHO-PLUMBATE

CAS: 1314-41-6

RTECS: OG5425000

Fraction By Weight: > 1%

OSHA PEL 0.2 MG/M3 (AS PB)

LEAD CHROMATE (SARA 313)

CAS: 1344-37-2

RTECS: GB2975000

Fraction By Weight: 15%

ACGIH TLV: .05PB.1CR03 MG/M3

MAGNESIUM SILICATE (AS NUISANCE DUST)

CAS: 14807-96-6

RTECS: WW2710000

Fraction By Weight: > 1%

OSHA PEL 20 MPPCF

ACGIH TLV: 2 MG/M3

ISO-PROPANOL (SARA 313) (VAPOR PRESSURE 44.00 MM HG @ 20F)

CAS: 67-63-0

RTECS: NT8050000

Fraction By Weight: 3%

OSHA PEL 400 PPM

ACGIH TLV: 400 PPM

TOLUENE (SARA III)

CAS: 108-88-3

RTECS: XS5250000

Fraction By Weight: 1 - 10%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Health Hazards Acute and Chronic:ACUTE: IRRITATION OF EYES & SKIN MAY
OCCUR WITH OVEREXPOSURE. CONTINUED BREATHING OF VAPORS MAY IRRITATE
RESPIRATORY TRACT CAUSING HEADACHE, NAUSEA & DIZZINESS. CHRONIC:
REPORTS HAVE ASSOCIATED REPEAT ED & PROLONGED OCCUPATIONAL
OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN & NERVOUS SYSTEM
DAMAGE.

First Aid:INHALE: GET FRESH AIR. RESTORE BREATHING IF NEEDED. TREAT
SYMPTOMATICALLY. EYE: FLUSH IMMED W/WATER FOR 15 MIN MINIMUM.
CONSULT DOCTOR. SKIN: WASH AREA W/SOAP & WATER. REMOVE CONTAM
CLOTHES. CONSULT D OCTOR IF IRRITATION PERSISTS. INGEST: DRINK 1-2
GLASSES WATER TO DILUTE. DO NOT INDUCE VOMITING. FOR SPONTANEOUS
VOMITING: HEAD BELOW KNEES- PREVENT ASPIRATION TO LUNGS. CONSULT
DR/POISON CNTRL CENTER

Flash Point Method:TCC
Flash Point:80.0F,26.7C
Extinguishing Media:FOAM, CO2, DRY CHEMICAL, WATER MIST
Fire Fighting Procedures:SMOTHER FLAMES WITH ONE OF THE ABOVE
EXTINGUISHING MEDIA. WATER MAY BE USED TO COOL DOWN UNOPENED
CONTAINERS IN VICINITY.
Unusual Fire/Explosion Hazard:CONTAINS FLAMMABLE SOLVENT. DO NOT USE IN
AREAS WHERE SPARKS OR OPEN FLAMES ARE PRESENT.

Spill Release Procedures:ELIMINATE ALL IGNITE SOURCES. WEAR PROTECTIVE
EQUIPMENT & RESPIRATOR. CONTAIN SPILL W/ABSORBENT & PUT INTO VAPOR
TIGHT CONTAINERS. PREVENT MATERIAL FROM CONTACTING WATER SOURCES OR
SEWERS LEADING TO S URFACE WATERS.

Handling and Storage Precautions:STORE IN AREAS DESIGNED TO COMPLY WITH
ANSI/ NFPA 20 FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE.
Other Precautions:GROUND CNTNRS WHEN POURING LIQUIDS & POWDERS TO AVOID
STATIC BUILD-UP. DO NOT USE UNTIL MFR'S SAFETY PRECAUTIONS HAVE
BEEN UNDERSTOOD. PROVIDE ADEQUATE VENTIL/RESPIR PROTECT TO REMOVE
DECOMP PRODUCTS WHEN WELDING/CUTTING COATED SURFACES.

Respiratory Protection:OUTDOOR/OPEN AREAS: USE APPROVED RESPIRATOR TO
REMOVE SOLID AIRBORNE PARTICLES OF OVERSPRAY DURING APPLICATION.
RESTRICTED VENTIL AREAS: USE APPROVED RESPIRATOR DESIGNED TO REMOVE
A COMBINATION OF PAR TICLES & VAPORS.
Ventilation:SUFFICIENT VENTIL, IN VOLUME & PATTERN TO KEEP THE AIR
CONTAMINANT CONCENTRATION BELOW CURRENT OSHA PERMISSIBLE LIMITS.
Protective Gloves:LONG/REPEAT: IMPERVIOUS TYPE REQUIRED
Eye Protection:FOR SPLASHES: SAFETY EYEWEAR
Other Protective Equipment:PREVENT PROLONGED SKIN CONTACT WITH
CONTAMINATED CLOTHING.
Work Hygienic Practices:WASH HANDS BEFORE EATING, SMOKING OR USING
WASHROOM FACILITIES.
Supplemental Safety and Health

HCC:F4
Boiling Pt:B.P. Text:148F,64C
Vapor Density:> AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:57.67

Stability Indicator/Materials to Avoid:YES
Stability Condition to Avoid:EXTREME HEAT, SPARKS OR OPEN FLAMES.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.